1966 Ford Mustang Coupe for sale in Denver, CO
Listed at $14,000 USD.
For sale is my 1966 Ford Mustang Coupe project. I purchased the car about six years ago in primer but was stored indoors for over 20 years in dry Colorado weather, with a seized inline-6 engine. Since then, I’ve put significant time, work, and new parts into converting it to a V8 setup and rebuilding/upgrading the engine, drivetrain, suspension, brakes, fuel system, floors, and chassis. A lot of the major mechanical and chassis work has already been completed, making this a solid foundation for someone looking to finish a classic 1966 Mustang V8 restomod. Engine 1983 Ford 302 V8 from a Crown Victoria Engine completely torn down and rebuilt Block bored .030 over New pistons and internal components Hydraulic cam New Hedman shorty headers New Holley carburetor HEI distributor/ignition with new wires Rebuilt engine runs and can be started and demonstrated for serious buyers Body, Floors & Chassis Rusted floor-pan sections were cut out, replaced, and welded in Entire chassis, including the engine bay, was sandblasted before recoating Chassis treated with POR-15 chassis coating Engine bay was properly treated, primed, and painted satin black to match the original 1966 Mustang engine-bay color Chassis is rust-free front to back Body is currently in project condition and ready for the next owner to finish Suspension, 5-Lug Conversion & Rear End The Mustang was originally an inline-6 automatic transmission, 4-lug car and has been converted to a 5-lug setup front and rear for the V8. Front disc brake setup New upper and lower front control arms New front springs for the 302 V8 New rear leaf springs for the V8 setup Refurbished Ford 8-inch rear end Rear drum brakes Wheels & Tires Original 5-lug Mustang wheels from another 1966 Mustang Wheels are in good condition Tires hold air but are older and are not roadworthy Tires should be replaced before road use Fuel System New fuel tank New fuel hoses and associated tank accessories/hardware Original fuel lines removed New stainless-steel fuel lines Higher-flow fuel setup to support the 302 V8 Brake System Front disc brakes / rear drum brakes Original brake lines removed New stainless-steel brake lines throughout Wilwood dual-bowl master cylinder Transmission & Clutch Converted to a manual transmission 3-speed manual transmission currently installed T5 5-speed manual transmission included with the sale T5 adapter included and compatible with the existing bellhousing New Wilwood hydraulic clutch system Clutch pedal setup completed with roller bearings for smoother pedal operation My plan was to finish the car with the T5 5-speed. The T5 adapter is compatible with the existing bellhousing, while the Wilwood hydraulic clutch and upgraded roller-bearing pedal setup are already completed. Interior & Seats Original 1966 Mustang seats included Original seats will need new covers/upholstery Also includes a set of power seats from a 1990s Mustang I planned to install the power seats for additional comfort and modern convenience Both sets of seats are included with the sale What Still Needs to Be Done This is not a finished or turnkey car. It is a project and will require additional work before it is road-ready. Based on my assessment, I estimate approximately 30–40 hours of additional work to get it to the running/driving stage, depending on the buyer’s experience and how they choose to finish the car. A significant amount of the expensive and time-consuming work has already been completed, including: Rebuilt 302 V8 Floor-pan repairs Sandblasted and recoated chassis Properly treated, primed, and satin-black engine bay Front-to-rear 5-lug conversion New suspension components Refurbished Ford 8-inch rear end Front disc / rear drum brake setup Stainless-steel brake lines New fuel tank, hoses, tank hardware/accessories, and stainless-steel fuel lines Manual-transmission conversion Wilwood hydraulic clutch and roller-bearing pedal setup T5 5-speed, compatible bellhousing adapter, and related components included I’ve put a lot of time, parts, and effort into getting this Mustang to where it is today, but I’m ready to let someone else take it across the finish line. $14,000 OBO Reasonable offers considered. Serious inquiries only, please. If you’re looking for a 1966 Mustang Coupe 302 V8 restomod project where much of the major mechanical, suspension, brake, fuel-system, drivetrain, and chassis work has already been completed, this is a great starting point. Clear and clean title in Hand. Bring a trailer. The car is not currently road-ready, and the existing tires should be replaced before road use. Note: I also have all the old original parts in hand, if someone wants to revert to the original suspension: rear and front or the transmission back to automatic, the gear lever and all in hand.
- Price
- $14,000 USD
- Mileage
- 66,000 miles
- Fuel
- gas
- Transmission
- manual
- Drivetrain
- rwd
- Body type
- Coupe
- Condition
- fair
Photos
Buy directly from the owner on Carsido Marketplace. Listing located in Denver, CO.

















